How To Guide - Pulsar Handbrake Adjustment
Posted: Sun Aug 28, 2016 2:58 pm
So I have seen on here that many people are finding that the handbrake on the Pulsar comes up too high and gets in the way when engaged, I decided to take some pictures of how you adjust it and make a post so you guys and girls can do it too.
Step 1:
Empty your cupholders and lift up your center armrest like shown.
IMG_20160610_140827_zps7fosqli3 by HRichmondPhotography, on Flickr
Step 2:
Place your fingers in the location shown and pull up, you will feel the panel come up as you pull.
IMG_20160610_140831_zpsp6gxfeqj by HRichmondPhotography, on Flickr
Step 3:
Lift up and remove the cupholders over the handbrake and place to one side.
IMG_20160610_140837_zpsmygzdqdg by HRichmondPhotography, on Flickr
Step 4: You should now see your handbrake assembly as shown here
IMG_20160610_140843_zpswu3jzclk by HRichmondPhotography, on Flickr
What you are looking for is this 10mm bolt.
[IMG_20160610_140849_zpssy2ug5ms by HRichmondPhotography, on Flickr
Step 5:
I found the best tool to adjust the handbrake was a 10mm ratchet spanner but if you dont have a ratchet one then a normal one will do just fine!
The way to adjust it is to have your foot on the footbrake and release the handbrake, this will allow you to place your tool of choice onto the nut and do it up, keep checking how far the handbrake can be pulled until you are happy!
Step 6:
Once you are happy with how your handbrake sits when engaged slide the cup holders back over the handbrake making sure to place the front of the cupholders in first, like shown and push down.
IMG_20160610_140902_zpsulym0syo by HRichmondPhotography, on Flickr
Step 7:
Once you have pushed the cup holders down and into place it should look like this!
IMG_20160610_140820_zpsbawbk2lc by HRichmondPhotography, on Flickr
Well done! You have successfully adjusted your handbrake and you only needed one tool!
I hope this has helped, let me know if you have any questions!
Step 1:
Empty your cupholders and lift up your center armrest like shown.
IMG_20160610_140827_zps7fosqli3 by HRichmondPhotography, on Flickr
Step 2:
Place your fingers in the location shown and pull up, you will feel the panel come up as you pull.
IMG_20160610_140831_zpsp6gxfeqj by HRichmondPhotography, on Flickr
Step 3:
Lift up and remove the cupholders over the handbrake and place to one side.
IMG_20160610_140837_zpsmygzdqdg by HRichmondPhotography, on Flickr
Step 4: You should now see your handbrake assembly as shown here
IMG_20160610_140843_zpswu3jzclk by HRichmondPhotography, on Flickr
What you are looking for is this 10mm bolt.
[IMG_20160610_140849_zpssy2ug5ms by HRichmondPhotography, on Flickr
Step 5:
I found the best tool to adjust the handbrake was a 10mm ratchet spanner but if you dont have a ratchet one then a normal one will do just fine!
The way to adjust it is to have your foot on the footbrake and release the handbrake, this will allow you to place your tool of choice onto the nut and do it up, keep checking how far the handbrake can be pulled until you are happy!
Step 6:
Once you are happy with how your handbrake sits when engaged slide the cup holders back over the handbrake making sure to place the front of the cupholders in first, like shown and push down.
IMG_20160610_140902_zpsulym0syo by HRichmondPhotography, on Flickr
Step 7:
Once you have pushed the cup holders down and into place it should look like this!
IMG_20160610_140820_zpsbawbk2lc by HRichmondPhotography, on Flickr
Well done! You have successfully adjusted your handbrake and you only needed one tool!
I hope this has helped, let me know if you have any questions!